I have 2 inch Hanldebars. Will the mount fit?

Sorry, the included mount will not fit. However, you can use double-sided adhesive, or velcro to instal on a flat surface also 

I have rubber valve stems. Is that a problem with this product?

These type of outer TPMS is not recommended for rubber stems. They will increase the pressure in the stems, so can cause the failure of the stems. You can use the inner tire type, such as Sykik SRTP400 

I read that range is good at least to 10 feet, is there farther capability? If another motorcycle is using the same SYSIK model would there be interference between the two motorcycles.

The range cannot be extended. Each sensor is paired to the head unit. There will not be any interference if other sendors are around.

can the battery in the display be replaced?

The battery can be replaced. But not recomanded, since the unit is waterproof and opening the unit will disturb that. You will need to use a waterproof sealent to close the unit back. You also have the option of jusdt purchasing the head unit alsone. You will then pair with your old sensors

I just bought the unit. When I need to recharge how do i charge it? Where do I plug into the unit? And what do i ug the other end of the coard into? Please be specific. I'm old and not a tech person.

On the side of the main unit, there is a small cover. Open the cover and see the mini USB port. Plug the cord included in your box here. Plug the otherside of the cord to a USB charger, like the one you use to charge your cell phone.

Received the SRTP-300, I can not get monitor to change from BAR to PSI or C to F. Seems to be locked on BAR-C?

turn on the unit by pree and holding lower button. When on, press and hold upper botton for few seconds. The display will go yo settings, showing BAR-PSI. Press lower button once (or towice) more to have PSI on the display only. Press and hold upper button for few seconds to go back to main display.
Let me know if any problems

How long does it take to fully charge the unit, and will it stop charging it automatically when its fully charged?

Depending on you USB Adapter, from 20 minuts to 2 hours to charge. Once done, it will stop charging, the battery icon on the display will show

Does the motorcycle need to be ridden for a while to "wake up" the sensors, or are they always sending signal to the display so that I know the pressures when I walk into my garage in the morning?

The sensors will stop sending signals when motorcycle has been stationary for a while. Otherwise they will drain the battery. Once there is a movement, the sensors will start again. You can tap the sensors to start them up as well

I would like to purchase a backup USB charging cable. What is the type of connector end that plugs into the monitor?

The cord you need is a USB to Micro USB. This cord is a standard that is used by most USB charged items. You probobly find them in your household, otherwise you can obtain one on SYKIK.com as well as other on line outlets such as Amazon or eBay

Hello, can it be use on an electric scooter that has an inner tube with slime in it?

yes, not a problem. As long as the stems are standard size, there will be no problem.

Just installed the SRTP300, but how long does it take for the monitor to recognize the sensors?

It seems you need to reset the sensors. Remove the sensors and re-instal again. This will reset

I lost the screen that displays de numbers. Can I buy only a new screen, as I already have the other stuff?

please click bellow link:
https://sykik.com/products/display-monitor-for-srtp300-400?_pos=1&_sid=2c42fc9ba&_ss=r

Or search for DISPLAY MONITOR FOR SRTP300-400

Please note, you will need to pair your sensors to the new monitor. If you need a new instruction manual, please let me know

I have metal valve stems that are threaded to accept screw on sensors on both inside and/or outside the wheel. Will your screw on sensors work inside the wheel?

The sensors for SRTP300 is only for outside of the wheel. For inside, you should look at SRTP400. These replaced you stems

I have just purchased the SYKIK Rider SRTP-300. Can these valve stem transmitters also be used with the phone app. The mounting bracket is much larger than my old system and I may prefer to use my phone rather than the handle bar display unit. Thanks

SRTP300 does not transmit with Bluetooth , it is radio wave that is more stable. Also can make the sensors fit in a smaller space. You cannot use them with your phone APP. I sugguest you look into a flat mount so you can place the monitor on your dash, fairing, gas tank ...

Will the display receive the sensor signals from the wheels if the display is mounted inside an enclosed vehicle?

Yes the monitor can receive the signals if installed inside the cab. The range of the signal will be reduced depending on the thickness of the cab. In a distance of about 10', there should not be a problem at all.

Can Sykik TPMS be used with Ride On Balancer/Sealer installed? Are the sensors potted/sealed?

Yes, they will work. The sensors are sealed

I am having trouble setting up my TPMS 300. Do you have a manual or website to help me out?

SRTP300 comes paired out of the box. If you are not getting readings when installed, please remove the sensors and re-install. For more help please contact support@sykik.com

HOW CAN THE SENSOR CREATE PRESSURE IN A RUBBER STEM? IT JUST MONITORS THE PSI AND TEMP

To monitor the tire pressure, the external sensors will bring the aire pressure from the tire to the stem, by pressing down the stem's little needle. in normal condition, this needle keeps the air in the tire trapped bellow the stem. the sensor will bring the air all the way up to the tip of the stem. Therefor increasing the air pressure in the stem to the air pressure inside the tire.

What is the minimum tire pressure it can monitor? For off-road use I like to go down to 1.0 bar, would that work? I also use slime in my tires, would it work with slime?

SRTP300 ranges from 0 to 99 PSI. So you can use for low as 0 pressure. Also the slime will have no effect on the system

can the sensors from the SRTP300 be configured to work with the android app as well?

Sorry, cannot. The APP based sensors comunicate with Bluetooth connection. SRTP300 connection is FM wave that is more stable and allows smaller size sensors.

Can this be used on a 90° METAL stems

This model can be used on a 90 degree stems, as long as they are metal. Please note you might have space limitations. The sensors are 1.5 CM (0.6 inch) in diameter. so you will need about half of that (from center of your stems) clearance arround the stem.

Is there a default setting and if so how do you get it?

there is a defualt setting, 29PSI for low and 44PSI for high.
You can change the setting in page 5 of the manual you find:

Parameter setting

• Maximum pressure alarm value can be set as high as 87PSI (6 BAR).
• Maximum pressure range can be displayed 99 PSI (up to 8 BAR).

High Pressure Setting:

• Press and hold SET button to enter settings.
• Press ＜ to choose "high pressure HI" as  below,
• Press SET button to setup high pressure alarm value.
• Press＜ to adjust the value desired
• Press SET to save.
• Press and hold SET button about 3s to save and exit to standby.

Low Pressure Setting:

• Press and hold SET button to setup
• Press ＜ to choose "low pressure LO" as below,
• Press SET button to setup low pressure alarm value.
• Press ＜ to adjust the value desired
• Press SET to save.
• Press and hold SET button about 3s to save and exit..

What is the replacement battery type for the tire pressure sensors on SRTP300? This should be documented in the user manual so we can buy spares before they are needed.

The replacement battery is CR1225. You are correct, we will include in the manual on the next publication

Can you still use phone app also with this unit?

The sensors on units with display use radio vawes that are more accurate and more stable. So cannot be used through APPs that use Bluetooth connection.

My motorcycle requires 28psi front and rear. Does this fall within the range this TPMS will monitor without setting off the low pressure alarm?

Yes, you can reduce the low setting as low as you like

Can it be changed to psi or is it stuck in bar measurement?

Yes, you can change between PSI and BAR, also between Fahrenheit and Celcius.

how often you should charge it?

The display unit will need to be charged every 3-6 months. Depending on usage.

Can you please elaborate on something I read on your FAQ list. It read that you can wake up the SYKIK Rider SRTP300 so that it will display the current pressures by tapping on it. Please explain. And will that process always work? I do not want to have to start riding the bike and then find out the pressure is off. Thanks in advance.

All TPMS sensors (including car sensors) will stop broadcasting when there is no movement. This is to save battery in the sensor. The sensors are motion activated, so when the sensor detects motion, it starts up.  Most of the times, just by starting your bike, the motion of the engine will trigger the start. Otherwise, you can move the bike a little, or shake the senso. 

I have these on two bike with great success. However, one sensor goes through a battery in 2-3 weeks while the others last months. Are replacement sensors available?

yes they are available. please take a look at the head unit or sensors, they have serial number on them. Do you see (Z) at the end of the serial number? If so, you have the current version, sensors are available on www.sykik.com. Jusr search for SRTP300.

How do I reset when replacing sensors

Are you trying to pair a new sensor? 

Pairing Sensors:

1-       Press SET (upper button) five times continuously to enter pairing mode

2-       Press ＜ (lower button) to choose the tire you wish to pair. Pairing tire will start to flash

3-       Tighten the sensor. The monitor will look for the sensor and displays the pressure and temperature.

4-       Press and hold SET (upper button) about 3s to save and exit to standby.

When moving does the unit display the current tire pressures all the time? Or only when there is a problem?

When moving, the pressure is measured and displayed updated, every few seconds. So it is always showing the pressure, updated every few seconds

When I received the unit it was showinf Bar-PSI -188 I have made numerous attempts to change to PSI and I am unable to get it to change . In setup it will show BAR and BAR PSI but not PSI alone. HOW DO I GET IT TO CHANGE TO PSI. I LIKE THE UNIT. I FOLLOWED THE INSTRUCTIONS. Same as problem listed on your website. IT IS STILL LOCKED ON BAR . Never goes to PSI Alone. Received the SRTP-300, I can not get monitor to change from BAR to PSI or C to F. Seems to be locked on BAR-C? turn on the unit by pree and holding lower button. When on, press and hold upper botton for few seconds. The display will go yo settings, showing BAR-PSI. Press lower button once (or towice) more to have PSI on the display only. Press and hold upper button for few seconds to go back to main display. Let me know if any problems

When showing BAR PSI, you should press the button on the top one time. It will go to one unit only (BAR in your case). When BAR flashing alone, press the lower button once to change to PSI. Once you have PSI flashing, press and HOLD the upper button to save and get out of setting.
Let me know if you need more help.

How do you do a factory reset

SRTP300 Reset

• Turn the display off by press and holding the lower button.
• Press and hold SET (upper) button and connect the charging cord, when the unit turns on, remove the charging cord, release the SET button.
• You will hear a BEEP, the unit is re-set.

Will these work with 90 degree metal valve stems?

Yes, newer generation of SRTP300 can air to internsl sensors. Just look gor (Z) at the end of serial number on the monitor

What type of battery goes in the valve sensor and how do you replace them?

SRTP300, takes watch battery : CR1225. You can open the sensor with the metal tool included in the box, and exchange the battery.

Will this device show me the real time tire pressure or just it just send a warning ping when the tire pressure falls outside of the selected range?

Display shows your tire pressure in real time, up dated every few seconds (while moving). When there is no movement in awhile, the sensors will go to sleep to save battery.

I have the SRTP300 on one of my bikes and am wanting to purchase another unit for my other bike. Will the 2 different units only read the sensors that came with the unit, or will it cause misreading since both motorcycles are parked side by side?

Each sensor is paired to a head unit. You will not have any problem by having 2 or more sets close to each other.

I have lost the battery changing tool for my SRTP300. Where can I get another one please?

on www.SYKIK.com search for your model: SRTP300 , all accessories will show up. https://sykik.com/products/battery-changing-device-for-srtp300-670?_pos=12&_sid=60030e902&_ss=r

Motorsycel The battery in the monitor is not working Cane i bay only the monitor?, (Srtp-400 dc5v-x 18j0041904)

yes, you can just replace the monitor. Please check the serial number located under the model number. Older generation, seral numbers are just numbers, our new generation serial numbers ends with "Z". Please let me know which version you have.

How accurate is the product in terms of pressure measurement?

Most user report good accuracy. For wireless gages, you should expect  a few PSI difference to direct gages.

I lost my lock nut changing tool, where can i find a new one and what is the size to look for

Please see below link
https://sykik.com/products/battery-changing-device-for-srtp300-670?_pos=10&_sid=f51cac979&_ss=r

Or, you can go to sykik.com, search for SRTP300, add accessories will show up.

I was wondering if the SRTP-300 can be used on a Tubeless system?

Not a problem. As long as your stems are metal, you should not have a problem

re: srtp300 would i be able to use a custom setting of 20 psi for the minimum ?

Yes, can go down as far as 15PSI

Can these sensors be used with tire sealant?

Yes, it will work fine

Some how I have changed the settings for low tire pressure for both front and rear and cannot get the monitor to go back to a single tire to increase the pressure setting. Both tires are blinking and will not go to one and the alarm is beeping. Please let me know how to reset.

To reset to factory defual: 
Turn off the head unit
Press and hold SET, connect the charging cable, when display comes on, remove the charging cable, then let go of SET button
The unit will beep and goes back to factory defualt.

I cannot seem to get the Setting to go to psi. It is stuck on bar. When it says bar psi is that psi? Or should it say psi only? That is my issue. I cannot get it to say just psi or to lock on bar psi if that is the psi reading. Why would it even have bar as an option? 95% of us use psi I’m sure.

when unit on, press and hold the SET (upper) button till the unit goes to setting mode. Once in setting, PSI  BAR will be flashing. Press SET (upper) button once. Will take you to setting for pressure. BAR or PSI (only one) will start to flash. using the lower button, you can change to your desire value (PSI in your case). Once PSI is flashing, press and hold SET to save and leave setting.
   US customers use PSI, but most other countries use BAR. That is why there is an option for BAR  PSI.

Can I pair a new sensor to my monitor?

Yes, you certainly can. When ordeing sensors, please take a look at your monitor. There is a serial numberon the side. If you see (Z) at the end, you have the new generation SRTP300. Otherwise you have older generation. choose the sensor accourdingly.

The rear pressure gauge is stuck at 32 psi. When I take it off the valve stem it doesn’t alarm that it’s off how do I reset??

It seems the battery in your sensore is dead. Please replece.

I have a SRTP300 unit mounted on Rubber Valve Stems. I just read this is not recommended, Am I in danger of valve stem failure. I have been using it for over 1 year with no problem.

The way the external sensors work, is that they will push the little pin inside the stem down, allowing the pressure riase to the top of stem. Some rubber stems are not strong enough to handel the pressure, and can rupture. Some stems are actually metal but have a rubber coating for protection. Please see if you actually have  rubber , or rubber coated stems. Since you been using the sensors for a long time, you probobly are ok, and your stems might be stron enough, that is your call. I sugguest to change the stems to metal to be sure.

Does the Monitor shut down automatically if there's no movement - and switch on again once the motorcycle moves? Or do I need to manually switch it off / on every time?

Yes, auto shut of and on. Also can be manually done as well